| 產地 | 河北 |
|---|---|
| 產品認證 | ISO2001 |
| 電池容量 | 1001mAh-2000mAh |
| 規格 | 85*35*25 |
| 類型 | 新款移動電源 |
| 適用范圍 | 中小型車輛啟動 |
| 適用類型 | 后備電源 |
| 輸入電壓 | 220.330 |
| 顏色 | 綠 |
| 品牌 | 孫大燈 |
| 加工定制 | 是 |
| 電源容量 | 1500毫安 |
| 是否支持太陽能 | 是 |
| 電芯類型 | 液態鋰離子電芯(18650) |
| LED等照明 | 是 |
產品簡介
啟動電源是汽車維修行業必備工具，具有電池充電，車輛啟動，焊接等功能。尤其在北方地區冬季使用，會在很大程度上減輕蓄電池的負擔，延長蓄電池的使用壽命，給消費者帶來極大方便。
一、啟動
1、首先確認所被啟動的車輛蓄電池電壓為12V或24V。正、負極不得接反。12V正極連接線連接到標有12V“+”的位置。24V正極連接線連接到標有24V“+”的位置。負極不分12V/24V均連接在標有起動“-”的位置。
2、用連接線將啟動電源和蓄電池正負極對應連接。
3、確認連接無誤：打開保護開關將電流調節旋鈕撥至**檔，開始起動車輛。如起動馬力不足可將電流調節旋鈕順時針方向調節。（也可以將電流調節扭直接調至起動檔，即**大檔）
二、充電
根據電池電壓用連接線接好，確認12V或24V。給12V電池充電將連接線連接在標有12V“+”的位置，給24V電池充電，將連接線接在標有24V“+”的位置。負極均接在標有充電“—”的位置（12V、24V均接在充電“—”的位置）
三、電焊
1、必須將連接線連接在24V位置。正極接在標有24V“+”的位置上，負極接在起動“—”的位置上。
2、調節電流旋鈕至焊接位置，也可根據焊條大小順時針調節電流增大。（也可直接將電流旋鈕調至焊接位置）
技術指標
| 型號 | **大起動電流（A） | 充電電流（A） | 輸入電壓AC（V） | 輸出電壓DC(V) | 頻率（Hz） | 適用車輛 |
| SDD-500A | 300 | 50 | 180-240 | 12、24 | 50/60 | 小型車輛啟動 |
| SDD-1500A | 1500 | 50 | 220-380 | 12、24 | 50/60 | 中、小型車輛啟動 |
| SDD-2500A | 2500 | 50 | 220-380 | 12、24 | 50/60 | 大、中型車輛啟動 |
Product Introduction
1、Starting power is necessary tool for vehicle maintenance industry. Its function is battery charging、vehicle starting、and welding etc., especially used in could case. A starting power largely reduces a burden of batteries, prolongs the service life of batteries, and provides a great convenience for consumers.
一、Starting
1、First of all, confirm the started vehicle battery voltage is 12 V or 24V. Positive and negative can not be connected in reverse. 12V anode is connected to the 12V positive position with “+”mark. 24V cathode is connected to 24V negative position with “+”mark. Negative does not distinguish 12V from 24V. Positive and negative are connected to the starting position with “-” mark.
2、With connection lines, the positive and negative poles of the starting power supplies and batteries are connected correspondingly.
3、Carefully confirm connection: open a protection switch, shift the current regulation knob to first gear; Then begin to start a car. If the starting horsepower is insufficient, clockwise adjust the current adjusting knob.
二、Charge
According to battery voltage, connection lines are connected tightly ,and make confirmation of voltage for 12.0 V or 24 V. Charging a battery with 12 V, make connection line to the 12 V position labeled as “+”. Charging a battery for 24 V, set connection line on 24 V position marked as “+”. Cathodes are all connected to charging position labeled as " - " (12V and 24V both are joined to charging " - " position)
三、Welding
1、A connection line must connect to 24V position. Positive electrode joins to the 24V position labeled as " + ", negative electrodes all are joined to the starting position labeled as “－”
2、Regulate a current knob to a welding position, Also can be based on a welding size, increase clockwise current.
(Also possibly and directly regulate a current knob to the welding position)